|
Clean the laser lens on a PS2 Why do this? If you find that disks don’t load properly (you get "Disk Read Error"), or some disks load but others don’t, it may be that there has been a build-up of dust on the laser lens. This can best be removed by disassembling the unit and carefully cleaning the lens. This is a repair you can easily do yourself by following this step-by-step guide. Note: This procedure involves removing the PS2 cover. This will invalidate the warranty. A tell-tale sticker will show the cover has been removed. Step 1 – Try a quick check to see if the laser is dirty. You may find that by opening the disk drawer and blowing hard into the player that you can dislodge some dust. If after doing this you find that the disk now works, the lens probably needs cleaning. Step 2 – Assemble the tools you’ll need.
To perform this your’re going to need to remove the PS2 covers and clean the laser lens. For this you’ll need: 1. Cross-point screwdriver (large) 2. Small flat blade screwdriver 3. Watchmaker's crosspoint screwdriver 4. Isopropal alcohol (isopropanol or Ethanol - similar to Methylated spirits) 5. Cotton buds 6. Manifier (Optioal) |
|
|
|
|
PSP analog stick replacement tutorial-this is our second psp repair tutorial and it deals with the second most common psp problem.A broken analog stick can be a real pain because it drifts or simply gets stuck in ne direction.This tutorial will show you how to remove the faceplate and replace the analog stick.
|
|
|
|
Installing a new umd door can be a tricky process.The following on how you can replace your own umd door so that you don’t have to buy a new psp from sony.Unfortunately you can not install the umd door without opening the system since there are 2 screws holding the umd door in place.Aa always ,you are taking your own risk for doing this yourself.Ebay or the author is not responsible for what you do to your psp,You also should note that opening your unit will void any type of warranty you might have left.
Parts list:
you will need a small tip pilllips screwdriver #000
small tip flat head screwdriver #1.0
your psp
a umd replacement door
Step 1.opening your psp unit
Insert your small screwdriver tip under the lip of the left side the button bar and slide upward until the bar is disconnected from the metal lcd housing.Then carefully unplug the button bars flex cable.By lifting the tab upwards and slidingthe cable out.
|
|
|
|
1. First you have to remove the PSP faceplate and the lcd screen assembly. If you dont know how to remove them take a look at the PSP screen replacement tutorial.
2. Remove the screws in this picture. The red triangles are behind the battery. Try to keep the screws for each step of the tutorial separate. Doing this will save you a lot of time when youre putting your PSP back together.
3. Use a flat head screwdriver to pry the lcd housing out of the PSP. When the tabs are out open the UMD door. You should now be able to get the lcd housing out of the PSP.
|
|
|
|
This may void your warranty,if you have a broken or damaged Lcd or backlight,this is what you will need to do to fix it.
If you are a complete idio ,please don’t try this.I accept no responsibility if you damage your psp.
|
|
|
|
PSP Analog Stick Replacement Tutorial
A broken analog stick is the second most common PSP problem.in this tutorial we will show you how to remove the faceplate and replace the PSP analog stick.
Symptoms of a broken PSP analog stick.
1.moves in its iwn
2.stuck in on e direction
3.top plastic part broken off.
Stuff you need:
1.Broken PSP
2.A couple of small screwdrivers (phillips)
3.New PSP analog stick/joystick
|
|
|
|
|
LCD troubleshooting PSP lcd replacement backlight repair fix monitor replace lcd screen flat roof replacement.
Construction the TN display suffers from limited viewing angles,Especially in the vertical direction,and some are unable to display the full 16.7 million colors(24-bit truecolor)available from morden graphics cards.These particular panels,with 6 bits per color channel as opposed to 8,can approach true 24-bit color using a dither method which quickly cycles pixels to simulate a given shade,which are noticeable to some and discomforting to others,overall color reproduction and linearity on TN panels is poor.Shootingcomings in display color gamut(often referred to as a percentage of the NTSC color gamut) can also be attributed to backlighting technology.it’s not uncommon for displays with CCFL(cold catchode Fluorescent lamps)based lighting to range from 40% to 76% of the NTSC color gamut,whereas displays utilizing white LCD backlights may perceivable by the human eye.Twisted Nematic displays contain liquid crystal elements which twist and untwist at varying degrees to allow light to pass through.When no voltage is applied to a TN liquid crystal cell,the light is polarized to pass through the cell.In protortion to voltageapplied,the lc cells twist up to 90 degrees changing the polarization and blocking the light’s path.By pproperly adjusting the level of the voltage most any grey level or transmission can be achieved.Until quite recently(c.2004)the superior brightness and viewing angle of color plasma panels,when compared to lcd,made them one of the most popular forms of display for HDTV.However since that time improvements in LCD technology have closed the gap dramatically,The much lower weight ,price and power consumption of LCD have seen them make large inroads into the former plasma market.Sony now only sell a very limited range of plasma screens and appear set to quit this market altogether.
|
|
|
|
This is tutorial will focus on replacing the psp laser assembly,but it can also be used to replace almost any other part of the psp to get the laser assembly you frist have to remove the motherboard,wirelss board lcd screen and housing dpad,poer switch board umd door etc.Make sure you have a few ziplock bags for screws and small parts. You can purchase a peplacement psp laser assembly in the zombie srtore. Symptoms of a broken PSP laser: PSP won’t play new disks. Game and movies freeze or skip, Slow loading Stuff you need: Sony PSP with a bad laser A few small screwdrivers (Philips #000,flat head) Needlenose pliers Ziplock bags for screws and small parts Patience,this isn’t an easy job: |
|
|
Disclaimer: Opening up your PSP will void your warranty! The following guide is meant to be informative and we accept no blame for any damage caused to your PSP if you decide to follow this How To.
Removing the Cover:
You will need a small Phillips (cross) screwdriver and ideally an anti static dust brush (available at PC stores) to replace your joystick on your PSP. Removing the cover of your PSP involves removing 5 small screws and the first three are fairly obvious. On the back of your case with the top facing away from you there are two screw holes, one toward the bottom of the case and one at the top right hand corner beneath the shoulder button. Next up, on the bottom of the PSP is a little silver screw that keep the front cover attached. Unscrew each of these and keep them somewhere safe.
|
|
|
|
How To Remove A Stuck Game From Xbox 360 Halo 3 is stuck inside your Xbox 360 and you want to get it out. There is a way to manually remove it. First you will want to unplug the power for a few minutes to let your Xbox reset. Re-attach the power cord and see if you can now eject your DVD.
If that did not work turn the power off and unplug it. Remove the face plate on you Xbox console. You will need a thick paper clip or something similar. Straighten one end of it out. With the face plate removed you will see 2 small holes right underneath the DVD player and one hole to the right.
Since Xbox uses 3 different DVD drives the procedure will vary. If you have a Samsung or Toshiba drive use the small hole on the right. Should be right underneath the X on the DVD drive faceplate. Push your straightened paper clip in the hole until you feel it hit the gear. The gear needs to be spun from left to right. Poke around until you find it then push in gently until you feel it move. You will see the tray start to move out.
For Hitatchi DVD drives go for the first hole on the left. Beng DVD drives will use the middle hole. This requires the most pressure to get the gear to turn. You will see the tray start to move.
Take your time and do not push too hard in case you are missing the correct spot. Once the tray starts to eject you can pull on it slightly to help it open. You should now be able to remove your Game.
Now why did your game get stuck in the first place? Could be a lot of different reasons. You may have to replace your DVD drive if you are having loading problems. |
|
|
|
|
|
|
Page 6 of 6 |
Repair Center
